name
 
SAUNA SPECIFICATIONS

When specifying for a Sauna for your commercial or residential project it is important to know the difference between the two types of Saunas offered, Precut and Prefabricated. One package may be perfect for your project and the other may not work at all. Below we have described the differences between these two packages and some instances where one would be preferable to another.

Precut or Custom cut Sauna packages: These packages require that the contractor frame and insulate the space prior to installing the kit. The contractor must frame the room with either wood studs or metal studs. Drywall must be installed over the metal studs and wood nailers installed over the drywall. After the room is framed it must be insulated and a vapor barrier installed. 1"x4" wood paneling is then installed horizontally over the studs or nailers using standard blind nailing procedures.

This kit includes materials only for the interior of the Sauna. The exterior of the room can be drywalled, tiled, paneled, or any other type of material can be used. The room layouts shown on this site are our standard room sizes. These standard rooms utilize the space most effectively and allow for safe bathing.

Reasons (Circumstances in which you would) to use a Precut Sauna package:

  1. Precut rooms can be almost any size or shape and can be worked into plans for bathrooms, master bedrooms, home and commercial gyms, recreation rooms, pool houses, basements, garages, and virtually anywhere where a permanent installation is preferred.
  2. The precut or custom cut Sauna must be used in Saunas that have custom shapes, custom dimensions, or have varying ceiling heights.
  3. Precut must be used if handicap accessibility if required.
Reasons not to use a Precut Sauna package:
 
  1. Precut Saunas are more labor intensive than the Prefabricated packages. If the home owner or the contractor do not have the knowledge or time to frame, insulate, and install the tongue and groove paneling one board at a time then the prefabricated room would be a better choice ( In the instance where SPRINGS SAUNA COMPANY is not contracted to perform part or all of the labor).
  2. If the location of the Sauna is temporary, Precut Saunas are not removable.
Prefabricated Sauna packages: These packages are pre-manufactured in the factory for quick and easy installation. This Sauna only requires that the contractor provide adequate space for the Sauna, a solid, level. waterproof surface, and appropriate power for the heater and the light. This kit includes interior and exterior materials for the Sauna. The prefabricated Sauna room is a complete room. It is framed, insulated, and paneled inside and out. The room is built in sections approximately 7' long and 2' wide. These paneled sections sit on a 2" x 4" base supplied by the manufacturer. The panels lock together using Finlandia's exclusive concealed locking system. Competitors use wood screws, that are not as strong, and require additional battens inside the Sauna, or require that the paneling be face nailed. These methods do not give the Sauna the same custom look or strength of the locking system. These rooms are pre-plumbed for electrical wiring. The electrical wiring enters the Sauna from the top and runs through the conduit to the heater or controls. This type of room requires a minimum of 3" of clearance for the sides and the ceiling panels to be installed.

Reasons to use a Prefabricated Sauna package:
 

  1. The Prefabricated Sauna is an excellent option when minimal labor is desired. This type of Sauna can be assembled in only a few hours saving valuable labor time.
  2. If the Sauna is to be placed outdoors, unless a permanent outdoor structure is erected to house the Sauna.
COMPARISON CHART
Framing
(Provided by)		 2x4 or 2x6 wood, or metal studs with drywall and wood nailers applied (Contractor) 2"x2" Fire walls and Ceiling with a 2"x4" Base (manufacturer)
Insulation R11 or R19 Foil Faced (contractor) R11 Foil Faced (manufacturer)
Vapor Barrier Type C Building Foil (contractor or manuf.) Type C Building Foil (manufacturer)
Interior Paneling 1"x4" Tongue and Groove (supplied by manuf. installed by contractor) 1"x4" T&G (supplied and installed by manufacturer)
Exterior Drywall, Tile, Paneling, etc. (contractor) Rough sawn Mahogany or 1/2"x4" Cedar (manufacturer)
Vents 4"x10" Set of registers and grills (supplied by manuf. installed by contractor) 4"x10" set of Registers and Grills (supplied and installed by manufacturer)
Electrical All wiring must be provided by the electrician. Including water tight flex to the heater Conduit is installed in the wall panels, the electrician must run his wire through the conduit to the heater

In both Precut and Prefab packages the Sauna door is pre-hung and ready to install, the benches are prebuilt to the appropriate lenght and width by the manufacturer, the contractor only has to install supports provided by manufacturer to set benches on. The heater, controls, and accessories are provided in the same fashion for both packages and the contractor installs these items in accordance with the instructions. These instructions only apply if Springs Sauna Company has not been contracted to install the package.